PC PROOF C7000 is a special Acrylic resin based water proof coating. Because of its excellent Flexibility and thixotropic nature is an ideal for use on vertical as well as horizontal surfaces. It is single Pack, very economical and pollution free water proof coating. Due to its white color, it has excellent Solar insulation properties.
Advantages
- Life and durability of the structure is increased.
- Easy application, no machinery required.
- Light weight compared to conventional roofing systems, thereby loading on the roofs is reduced.
- Provides seamless and joint free seal throughout the surface, which is impervious to water.
- Lower labor cost due to easy, simple and quick application, leading to quick completion and time Saving.
- Provides insulation due to solar reflection.
- Excellent bonding to most building materials.
- It Provide protective membrane for polyurethane foam insulation.
Areas of Application / Uses
- Water proofing of plaza, car park deck.
- Water proofing cum decorating of external plastered walls.
- Water proofing of new surfaces as well as for the repairs of old surface, whether previously Treated or not.
- Suitable for horizontal as well as vertical surfaces like flashings.
- Water proofing of roof slabs, terraces, balconies, sun shades (chajjas), parapet walls, etc.
- Water proofing of flashing, roof edgings, gulley's, steeply pitched designs, etc.
- PC PROOF C7000 provides additional water proofing and protection when used as base And/or intermediate coat in brick bat coba and/or IPS floorings.
- PC PROOF C7000 is optimally suitable for application on structures having complicated geometry like domes, arches, shells, folded plates, paraboloids, corrugated sheets, etc.
- For garden, swimming pools, basement, sandwich application is recommended. For details, refer our technical department.
Application Instructions
Surface should be free from oil, grease and loose particles. In case of metal surface, remove rust and contamination for better protection, if the surface has been already treated with asphalt or bitumen coatings or roofing's felts and any blisters, peel-off traces, loose laying, etc. must be cut away and be properly filled. Masonry joints must be flush jointed. In case of tiling the roof, terrace, balcony or sun shade, the joints between the tiles should be properly filled to avoid water penetration through the joints. Mix well the container. Apply primer coat of PC PROOF C7000 i.e. 25% - 30% diluted with water by brush, spray or roller. After the primer coat is completely dried, apply minimum two coats of undiluted PC PROOF C7000.1t is very important to ensure each coat is totally cured (i.e. 8 hours at 30oC) before the next coat is applied. For better result use PC PROOF C7000 GLASS FIBRE REINFORCING AGENT embedded into first coat of PC PROOF C7000 while still wet mainly expansion areas joints with parapet. All brushes and tools should be cleaned by water immediately after use. PC PROOF C7000 can be diluted with water (5-10%) for easy application.
Coverage
Coverage depends upon the nature of the surface to be applied. But on average, smooth surface will give First Coat - 450 gm/m2 to 400 gms/m2. (Second coat). Two coats will give 1 mm dry film thickness.
Safety
Non - hazardous. If ingested, seek medical advice immediately
Storage
Minimum 12 months in unopened container. Store away from sunlight and preferably below 30oC.
Packing
PC PROOF C7000 is available in 20 kg. pail, 200 kg. Drum.
Technical Data
| APPEARANCE | White Thixotropic |
| SOLID CONTENT | 68% ASTM C-836, ASTM C 898 |
| SPECIFIC GRAVITY | 1.25 ± 0.1 |
| THICKNESS COAT | Approximately 1.0 mm, Wet Film. |
| RE-COAT INTERNAL | 4 Hours minimum. |
| SURFACE DRY TIME | None, after 4 Hours 16 Mils wet Film. |
| CURING TIME | 48 Hours. |
| TENSILE STRENGTH | 500 psi, ASTM D-412. |
| HARDNESS SHORE A | 60, ASTM D-2240 |
| PERMEANCE | 2.8 PERMS @ 20 Mils Dry Film. |
| PERMEABILITY | 0.05 PERMS inches. |
| TEMPERATURE LIMITS 20 MILS | -29°C +93°C |
| CRACKING | NONE NONE |
| TENSILE STRENGTH | 430 psi 430 psi |
| ELONGATION | 460% 460% |
| METHODS OF APPLICATION | Brush, Roller, Spray or Squeegee. |
All information is given in good faith on the results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since we don't have any control on site conditions and its uses.
PC THANE PU
(Polyurethane Top Coat)
PC THANE PU TOPCOAT is single component based on the innovative PUD Technology which enables, long-chain polyurethane macromolecules to be incorporated in a water medium, forming stable dispersions.
Read More